How to Remove Baseboard Heater

In these times, the heating of the socket is becoming more and more obsolete. Therefore, it is always a good time to replace this heating system with a more adequate and efficient one. To do this, you must follow a series of steps so as not to damage your home too much in the process.

If you are living in a home that is already a few years old, and therefore some old radiant base unit, then the following steps will be very useful to modernize your heating once and for all.

Also, there are a set of excellent reasons not to miss the opportunity.

While we are all witnessing the great number of new advances and discoveries within the laws of thermodynamics, it seems a bit contradictory and surprising to know that old heating systems are still preserved in many homes.

This can be explained due to two reasons. The first of these is that many residents do not have the appropriate knowledge that allows them to remove their heating systems by baseboards. Nor will they be willing to pay large sums of money and hire skilled labour to handle the issue.

The second reason is that in many cases a new heating system may seem a bit expensive for certain users. This is not only due to the cost of the product they wish to buy, but also because they must also spend money on their installation.

Therefore, in this case, you will not need to spend these important sums of money since you can get rid of your baseboard heating systems, by following the instructions below.

Then to begin with the renovation of your home, at least when it comes to heating, start by performing the following steps.

The heating system must be turned off

Before starting to touch any of the heating parts, you should check that the heating is permanently turned off. To do this, you must go to the circuit breaker box in your home, and turn off your heating system.

To achieve this, you usually only have to turn the appropriate button to the off position. In the case of having an old switch system, you should pay attention to some precautions. This means that you must shut down your system carefully as it could be a bit complicated.

Consider that if it is an old house and an old heating system, the switch system will share this same characteristic, which increases the degree of danger.

Your old system must be unscrewed

To unscrew the baseboard heating system, you must have some suitable tools. Therefore, the two best options will be to have an electric drill or a screwdriver on hand. If you do not have any of these tools, it is generally not recommended to perform the task. This is because it will only produce damage to your current heating system.

After obtaining the indicated tools, you can remove the important screws that hold your system. Normally this usually means just removing the screws from the motherboard. In this way, you will be able to expose the wall that is behind the inside. It is recommended in this case to perform each step with proper precaution in order not to damage any of the components.

Continue to remove the heater itself from your wall

It is essential to perform each movement and each step with the appropriate smoothness. Remember that this device includes a series of components that are sensitive and vulnerable. Then, properly continue to completely disconnect your heating unit from the wall. You should pay attention not to damage any wall or damage the paint during this procedure.

It would be an excellent idea to have a flat screwdriver to perform the task. Although also another recommended option is to move the unit with a knife. If you consider that you will not be able to do just the job, or at least it will cost you a lot to do so, you can request additional help throughout the task.

If you are considering using some other tool to perform this step, keep in mind that a larger tool could damage a wall or perhaps paint and even cause yourself or damage.

Then you must leave the wires exposed

This part can be relatively simple since you will have to unscrew the small box to get the wiring panel open. It is quite common for this box to be at one end of your heater.

You may also like Best Indoor Electric Heaters for large rooms

In this case, if you have any doubts, check again that the power is off. I don’t think you want this to be your last job.

Then once you have checked the power you can remove the panel and finally remove the wire nuts.

Cut the wires carefully

After having the cables securely fastened with the appropriate tool, make a precise and careful cut over them.

Use enough electrical tape in the appropriate places to avoid future damage to any person.

Then you must gather all the cables and wind them up, although you should always check that the tips are properly separated. This will be of great help when you decide to install a new heating system.

Finish the work with a temporary seal

The temporary seal is a useful and safe element when children or babies are wandering around the home. Using glue you can ensure that no household member suffers any damage.

Screw the lid on the wall and when your new heater is ready to be installed, just remove this lid. However, it is recommended that a professional help you with the new heating system station.

FAQs

These simple steps will teach you how to remove the baseboard heater. So saving money on hiring a professional is now possible simple and easy.

Choosing to do these happened by yourself will give you greater autonomy in the parts of your heating system as well as other parts in general.